How To Replace ABS Sensor Chevy Silverado? [5 Easy Steps]

The ABS is a blessing for modern vehicles, including the Chevy Silverado. Though it’s a great braking mechanism, sometimes it may not work properly. In that case, you’ll have to replace the ABS sensor along with other stuff. 

If you’re wondering how to replace the ABS sensor Chevy Silverado, this article is for you. In this article, I’ll be discussing ABS sensors & how to replace them in a step-by-step manner. 

ABS Sensor: What it is & How Does it Work?

ABS Sensor is an important element of the whole Anti-Lock Braking System (ABS). This sensor reads the rotational speed of each & every wheel of the car & gives reports to the Electronic Control Unit.

Later on, when the sensor detects a wheel is about to lock up – it releases & re-apply the braking procedure for a smooth braking experience. 

By using ABS instead of Hydraulic, you’re saving the tires being worn out too soon & yourself from unwanted slippage/accidents. 

The hydraulic brake system completely locks the wheel & causes slippage. However, the ABS allows you to brake & steer at a time that offers smooth braking while avoiding slippage. 

When Should You Replace The ABS Sensor?

The main mechanism of the ABS is to stop the car smoothly & the ABS sensor plays a vital role here. If you ever feel disappointed with your ABS, it might indicate issues with the module or the sensor. 

If your ABS is acting up, you might need to replace the sensor first as it’s cheap & won’t take much time on replacement. Here are the symptoms of a bad ABS or ABS sensor:

  • The ABS Light Will Turn On
  • Brakes Will Take Longer To Stop Car
  • Less Stability Under Wet or Icy Driving Conditions

If you notice any of the symptoms mentioned above, inspect your ABS & replace the ABS sensor first. 

How Much Does it Cost To Replace The ABS Sensor?

The ABS sensor is cheap, costing around $40 to $50. If you are not willing to do the replacement on your own, you can pay around $90 for the labour fee & he’ll take care of it. 

This replacement task isn’t that hard & you can do it even without much technical knowledge. Follow the next segment of this article to know how to replace the ABS sensor on a Chevy Silverado. 

How To Replace ABS Sensor Chevy Silverado: 5 Steps Guide

Like every other replacement, you can’t perform this operation barehanded. Here is the equipment you’ll need to do this replacement: 

  • 5mm & 18mm Screwdriver 
  • Hammer 
  • Jack & Hydraulic Floor Jack 

Considering you’re ready with the equipment, let’s get started with the step-by-step guide: 

Step 1: Remove The Wheel 

First of all, you’ll have to remove the wheel first. You’ll need to raise the upper part of your car using a hydraulic floor jack & hold it with some jack stands. Later on, use a torque wrench & wheel chocks to pull off the wheel. 

Step 2: Detach The Caliper 

After removing the wheel, you’ll have to detach the calliper. An 18mm bolt will be holding the calliper. Remove the bolt using an 18mm screwdriver & detach the calliper. Don’t let it hang as it may leak brake fluid. Instead, put it up somewhere.

Step 3: Detach The Rotor

The ABS sensor is located just behind the rotor. A 5mm bolt is holding this rotor. Unscrew the bolt & gently remove the rotor for better accessibility to the sensor. 

Step 4: Remove & Reinstall The ABS Sensor 

After removing the rotor, you can easily access the ABS sensor. Now remove it properly & match it with the new one. If it matches, reinstall the new ABS sensor. 

Step 5: Reattach The Caliper & Wheel 

After doing everything as mentioned above, now do the rest in reverse. You’ll have to reattach the calliper along with the wheel & you are all set. 

Common Mistakes While Replacing The ABS Sensor

If you’re new to Do-It-Yourself type work & attempting to replace the ABS sensor for the first time, you might commit some mistakes. Still, try avoiding these common mistakes mentioned below: 

  • Hanging The Caliper Downward
  • Not Using Proper Manual While Reprogramming The Sensor After Installation 

Frequently Asked Questions – FAQ

Can I Replace The ABS Sensor As A Newbie?

Replacing ABS sensors is an easy task & anybody can do it with proper equipment. Even if you’re just getting started with DIY work, you can replace the ABS sensor without much difficulty. 

Can You Clean The ABS Sensor?

Yes, you can & should clean the ABS sensor. You can easily clean your ABS sensor using a soft cloth/rag & mild soapy water. Don’t use any chemical solution while cleaning your ABS sensors. 

Does ABS Sensor Need To Be Reprogrammed?

Yes, you’ll have to reprogram each ABS sensor after new installations. The programming procedure varies from truck to truck & you’ll have to get your own while reprogramming.   

Conclusion 

I hope this article was informative enough tutoring you on how to replace the ABS sensor of Chevy Silverado. Now you know the basics of ABS sensors & the method of replacing them. 

Whether you’re doing the replacement on your own or hiring an experienced technician from an auto shop – it’s up to you. Still, it’s better to know the process to do it yourself in the future for sure.

Related Posts: